Author Archives: Elliot Williams

FLEX Pager Protocol in Depth

Posted on by

We love pager hacks. One of our earliest head-slappers was completely reverse-engineering a restaurant pager’s protocol, only to find out that it was industry-standard POCSAG. Doh!

[Jelmer] apparently scratches the same itch, but in the Netherlands where the FLEX protocol is more common. In addition to walking us through all of the details of the FLEX system, he bought a FLEX pager, gutted it, and soldered on an ATMega328 board and an ESP8266. The former does the FLEX decoding, and the latter posts whatever it hears on his local network.

These days, we’re sure that you could do the same …read more

Continue reading FLEX Pager Protocol in Depth→

Making a Cheap Radar Unit Awesome

Posted on by

[JBeale] squeezed every last drop of performance from a $5 Doppler radar module, and the secrets of that success are half hardware, half firmware, and all hack.

On the hardware side, the first prototype radar horn was made out of cardboard with aluminum foil taped around it. With the concept proven, [JBeale] made a second horn out of thin copper-clad sheets, but reports that the performance is just about the same. The other hardware hack was simply to tack a wire on the radar module’s analog output and add a simple op-amp gain stage, which extended the sensing range well …read more

Continue reading Making a Cheap Radar Unit Awesome→

Get Inside a TCXO Clock Chip

Posted on by

[Pete] wondered how real-time clock modules could be selling on eBay for $1.50 when the main component, the Maxim DS3231 RTC/TCXO chip, cost him more like $4 apiece. Could the cheap modules contain counterfeit chips?

Well, sure they could. But in this case, they didn’t, and [Pete] has the die shots to prove it. He started off by clipping the SOIC leads rather than desoldering — he’s not going to be reusing this chip after he’s cut it in half. Next was a stage of embrittling the case by heating it up with a lighter and dunking it in water. …read more

Continue reading Get Inside a TCXO Clock Chip→

Everything You Need To Know About Logic Probes

Posted on by

We just spent the last hour watching a video, embedded below, that is the most comprehensive treasure trove of information regarding a subject that we should all know more about — sniffing logic signals. Sure, it’s a long video, but [Joel] of [OpenTechLab] leaves no stone unturned.

At the center of the video is the open-source sigrok logic capture and analyzer. It’s great because it supports a wide variety of dirt cheap hardware platforms, including the Salae logic and its clones. Logic is where it shines, but it’ll even log data from certain scopes, multimeters, power supplies, and more. Not …read more

Continue reading Everything You Need To Know About Logic Probes→

Maywa Denki’s Nonsense Machines

Posted on by

We just spent a few hours trying to figure out Japanese techno-performance-art-toy company [Maywa Denki]. As self-described “parallel-world electricians”, the small art collective turns out strange electro-mechanical instruments, creates bellows-powered “singing” sculptures, and puts on concerts/demos/lectures. And if you desperately need an extension cord in the shape of a fish skeleton, [Maywa Denki] has you covered. Writing about art is like dancing about economics, so first we’ll just drop a few of our favorites and let you decide.

On the serious art front are “nonsense machines” like SeaMoonsII and Wahha Go Go. The most iconic performance piece is probably the …read more

Continue reading Maywa Denki’s Nonsense Machines→

The End of Arduino 101: Intel Leaves Maker Market

Posted on by

This looks like the end of the road for Intel’s brief foray into the “maker market”. Reader [Chris] sent us in a tip that eventually leads to the discontinuation notice (PCN115582-00, PDF) for the Arduino 101 board. According to Intel forum post, Intel is looking for an alternative manufacturer. We’re not holding our breath.

We previously reported that Intel was discontinuing its Joule, Galileo, and Edison lines, leaving only the Arduino 101 with its Curie chip still standing. At the time, we speculated that the first wave of discontinuations were due to the chips being too fast, too power-hungry, and …read more

Continue reading The End of Arduino 101: Intel Leaves Maker Market→

Duocopter Does it With Two Fewer Propellers

Posted on by

Quads are a great ‘copter design. The paired blades counteract each others’ torque, and varying the relative speeds of the four motors makes it easy to steer. But what if you could get by with fewer blades, substituting a significantly fancier control algorithm?

[Dirk Brunner]’s DuoCopter drone uses two propellers that counter-rotate, and it steers by increasing and decreasing the speed at which the blades rotate within a single revolution. Spinning faster on one side than the other makes it tilt. Saying this is one thing, but getting the real-time control algorithms up and running is another. From the video …read more

Continue reading Duocopter Does it With Two Fewer Propellers→

RoGeorge Attacks a Pulse Meter

Posted on by

The “Crivit Sports” is an inexpensive chest-strap monitor that displays your current pulse rate on a dedicated wristwatch. This would be much more useful, and presumably more expensive, if it had a logging option, or any way to export your pulse data to a more capable device. So [RoGeorge] got to work. Each post of the (so-far) three-part series is worth a read, not the least because of the cool techniques used.

In part one, [RoGeorge] starts out by intercepting the signals. His RF sniffer? An oscilloscope probe shorted out in a loop around the heart monitor. Being able to …read more

Continue reading RoGeorge Attacks a Pulse Meter→

I am an Iconoscope

Posted on by

We’d never seen an iconoscope before. And that’s reason enough to watch the quirky Japanese, first-person video of a retired broadcast engineer’s loving restoration. (Embedded below.)

Quick iconoscope primer. It was the first video camera tube, invented in the mid-20s, and used from the mid-30s to mid-40s. It worked by charging up a plate with an array of photo-sensitive capacitors, taking an exposure by allowing the capacitors to discharge according to the light hitting them, and then reading out the values with another electron scanning beam.

The video chronicles [Ozaki Yoshio]’s epic rebuild in what looks like the most amazingly …read more

Continue reading I am an Iconoscope→

Hackaday Prize Entry: Dongle For A Headless Pi

Posted on by

Mass production means that there’s a lot of great hardware out there for dirt cheap. But it also means that the manufacturer isn’t going to spend years working on the firmware to squeeze every last feature out of it. Nope, that’s up to us.

[deqing] took a Bluetooth Low Energy / USB dongle and re-vamped the firmware to turn it into a remote keyboard and mouse, and then wrote a phone app to control it. The result? Plug the USB dongle in, and the computer thinks it sees a keyboard and mouse. Connect the phone via BLE, and you’re typing …read more

Continue reading Hackaday Prize Entry: Dongle For A Headless Pi→