Author Archives: Elliot Williams

Piezomagnetic Trick Shrinks 2.5 GHz Antennas

Posted on by

To a ham radio operator used to “short”-wave antennas with lengths listed in tens of meters, the tiny antennas used in the gigahertz bands barely even register. But if your goal is making radio electronics that’s small enough to swallow, an antenna of a few centimeters is too big. Physics determines plausible antenna sizes, and there’s no way around that, but a large group of researchers and engineers have found a way of side-stepping the problem: resonating a nano-antenna acoustically instead of electromagnetically.

Normal antennas are tuned to some extent to the frequency that you want to pick up. Since …read more

Continue reading Piezomagnetic Trick Shrinks 2.5 GHz Antennas→

Bodging on More Flash Memory

Posted on by

[Curmudegeoclast] found himself running out of flash memory on a Trinket M0 board, so he decided to epoxy and fly-wire a whopping 2 MB of extra flash on top of the original CPU.

We’ll just get our “kids these days” rant out of the way up front: the stock SAMD21 ARM chip has 256 kB (!) of flash to begin with, and it only has five GPIO pins, for a 51 kB / pin ratio! And now he’s adding 2 MB more? That’s madness. The stated reason for [Curmudegeoclast]’s exercise is MicroPython, which takes up a big chunk of flash …read more

Continue reading Bodging on More Flash Memory→

1.5 Million Dollars Buys 850,000 LEDs and 29 Raspberry Pis

Posted on by

You think you like RGB LEDs? Columbus, OH art professor [Matthew Mohr] has more blinkenlove than you! His airport-scale installation piece is an incredible 850,000 RGB LEDs wrapped around a 14-foot tall face-shaped sculpture that projection-maps participants’ faces onto the display. To capture images, there is also a purpose-built room with even illumination and a slew of Raspberry Pi cameras to take pictures of the person’s face from many angles simultaneously.

Besides looking pretty snazzy, the scale of this is just crazy. For instance, if you figure that the usual strip of 60 WS2812s can draw just about 9.6 watts …read more

Continue reading 1.5 Million Dollars Buys 850,000 LEDs and 29 Raspberry Pis→

1.5 Million Dollars Buys 850,000 LEDs and 29 Raspberry Pis

Posted on by

You think you like RGB LEDs? Columbus, OH art professor [Matthew Mohr] has more blinkenlove than you! His airport-scale installation piece is an incredible 850,000 RGB LEDs wrapped around a 14-foot tall face-shaped sculpture that projection-maps participants’ faces onto the display. To capture images, there is also a purpose-built room with even illumination and a slew of Raspberry Pi cameras to take pictures of the person’s face from many angles simultaneously.

Besides looking pretty snazzy, the scale of this is just crazy. For instance, if you figure that the usual strip of 60 WS2812s can draw just about 9.6 watts …read more

Continue reading 1.5 Million Dollars Buys 850,000 LEDs and 29 Raspberry Pis→

Polyurethane, Meet 3D Printing

Posted on by

3D printing makes prototyping wonderful. But what do you do when your plastics of choice just aren’t strong enough? For [Michael Memeteau], the answer was to combine the strength of a vacuum-poured polyurethane part with the ease of 3D-printed molds. The write-up is a fantastic walk through of a particular problem and all of the false steps along the way to a solution.

The prototype is a connected scale for LPG canisters, so the frame would have to support 80 kg and survive an outdoor environment. Lego or MDF lattice were considered and abandoned as options early on. 3D printing …read more

Continue reading Polyurethane, Meet 3D Printing→

Doomed Incandescent Light Blinker

Posted on by

[Jānis]’s entry for the Flashing Light Prize was doomed from the start. Or should we say Doomed? It was a complicated mess of Rube-Goldbergery that essentially guaranteed that he’d have no time for making a proper video and submitting and entry. But it also ran Doom. Or at least ran on Doom.

(Note: [Jānis] sent us this hack in the e-mail — there’s no link for this blog post. You’re reading it here and now.)

It starts with a DC motor salvaged from a DVD player that spins a wheel that flips a switch back and forth, which in …read more

Continue reading Doomed Incandescent Light Blinker→

Wooden Word Wristwatch Wows Woomies

Posted on by

[HakuG] wanted to make a watch for his roommates, and had a design project due. He killed two birds with one stone, and then some. The result is a classic word clock, but with a refined all-wood look that’s also small enough to wear on your wrist.

Nothing good ever comes out right the first time, and the log of [HakuG]’s different versions is full of different attempts, all of them just fine in their own right, but none of them “perfect”. Kudos to [HakuG] for sticking with it and refining the project far past the initial prototype stage to …read more

Continue reading Wooden Word Wristwatch Wows Woomies→

Wooden Word Wristwatch Wows Woomies

Posted on by

[HakuG] wanted to make a watch for his roommates, and had a design project due. He killed two birds with one stone, and then some. The result is a classic word clock, but with a refined all-wood look that’s also small enough to wear on your wrist.

Nothing good ever comes out right the first time, and the log of [HakuG]’s different versions is full of different attempts, all of them just fine in their own right, but none of them “perfect”. Kudos to [HakuG] for sticking with it and refining the project far past the initial prototype stage to …read more

Continue reading Wooden Word Wristwatch Wows Woomies→

Filaween 2.0 is Go

Posted on by

[Thomas Sanladerer] is at it again: testing all of the 3D-printer filaments that are fit to print (with). And this year, he’s got a new and improved testing methodology — video embedded below. And have a search for “filaween2” to see what he’s reviewed so far. There’s some sexy filaments in there.

We really love the brand-new impact strength test, where a hammer is swung on a pivot (3D printed, natch), breaks through the part under test, and swings back up to a measurable height. The difference in swing height reflects the amount of energy required to break the test …read more

Continue reading Filaween 2.0 is Go→

Complete IR Control

Posted on by

What can you do with an IR remote? How about anything? Maybe not. We’ll settle for issuing arbitrary commands and controlling tasks on our computer.

The first step in [Fungus]’s hack is straightforward: buy an IR receiver for a buck, plug it into an Arduino, and load up some IR-decoding code. If you haven’t done this before, you owe it to yourself to take some time now. Old IR remotes are very useful, and dead simple, to integrate into your projects.

But here comes the computer-control part. Rather than interpret the codes on the Arduino, the micro just sends …read more

Continue reading Complete IR Control→