Author Archives: Gerrit Coetzee

App Control With Ease Using Blynk

Posted on by

App development is not fun for everyone, and sometimes you just want to control a device from your phone with minimal work. Blynk appears to be a fairly put-together library for not only hooking up any Arduino or esp8266 to a phone through WiFi, but also through the net if desired.

Install the app onto your iPhone or Android device. Install the libraries on your computer. Next, modify your Arduino source to either pass direct control of a pin to Blynk, or connect Blynk to a virtual pin inside your code for more advanced control. If you want to go …read more

Continue reading App Control With Ease Using Blynk→

Materials To Know: Tooling and Modeling Board

Posted on by

I was in a fit of nerd glee the first time I used tooling board. I’d used MDF for similar purposes before, and I doubt I ever will again. Called Renshape, Precision Board Plus, or that green stuff people on another continent buy; it’s all the same extremely useful, unfortunately expensive, stuff. It’s hard to pin down exactly what tooling board is. Most of the blends are proprietary. It is usually a very dense polyurethane foam, sometimes by itself, sometimes with a fine fiber filler.

What makes tooling board so good is its absolute dimensional stability and its general apathy …read more

Continue reading Materials To Know: Tooling and Modeling Board→

Turn A Free Flashlight Into LED Strips

Posted on by

Harbor Freight is always trying to sweeten the deal by throwing in a free flashlight, or a multimeter with a CAT III rating so poorly-met it might as well be a hand grenade. We usually donate the meters to our local hackerspace, but the flashlights tend to accumulate around the shop. Aside from borrowing the occasional magnet, we’ve not found a good use for them till now.

[Ben Brandt] realized that a ultra-low cost board such as the one likely to be in a free flashlight is probably going to contain a very easily hackable single-sided board. Which is exactly …read more

Continue reading Turn A Free Flashlight Into LED Strips→

Monitor A Serial Port From Anywhere

Posted on by

This simple WiFi serial port monitor would have saved us a lot of trouble. We can’t count how many times where being hooked into an Arduino with USB just to get the serial out has nearly been more trouble than it’s worth. Times where we sat cross-legged on the floor and could choose comfort or accidentally shifting the set-up and ruining everything, but not both.

[Frenky]’s set-up is simple and clever. The Ardunio’s serial out is hooked to an ESP8266. The Arduino spams serial out to the ESP8266 in its usual way. The ESP8266 then pipes all that out to …read more

Continue reading Monitor A Serial Port From Anywhere→

Tiny Open Source Robot

Posted on by

We watched the video introduction for this little open source robot, and while we’re not 100% sure we want tiny glowing eyes watching us while we sleep, it does seem to be a nice little platform for hacking. The robot is a side project of [Matthew], who’s studying for a degree in Information Science.

The robot has little actuated grippy arms for holding a cell phone in the front. When it’t not holding a cellphone it can use its two little ultrasonic senors to run around without bumping into things. We like the passive balancing used on the robot. Rather …read more

Continue reading Tiny Open Source Robot→

It’s Time the Software People and Mechanical People Sat Down and Had a Talk.

Posted on by

With the advances in rapid prototyping, there’s been a huge influx of people in the physical realm of hacking. While my overall view of this development is positive, I’ve noticed a schism forming in the community. I’m going to have to call a group out. I think it stems from a fundamental refusal of software folks to change their ways of thinking to some of the real aspects of working in the physical realm, so-to-speak. The problem, I think, comes down to three things: dismissal of cost, favoring modularity over understanding, and a resulting insistence that there’s nothing to learn. …read more

Continue reading It’s Time the Software People and Mechanical People Sat Down and Had a Talk.→

Social Engineering Your Way To The Target PA System

Posted on by

If we were to express an official view of the what these guys did once they hacked into a Target store’s PA system, we’d have to go with definitely uncool. However, it’s good to know that phone phreaking and good ol’ social engineering isn’t dead yet. Many of us got our start by playing with the systems around us.

Anyone could call into a Target store and request to be transferred to the PA’s extension code, which was the same everywhere. If the person transferring the call wasn’t quick on their feet, the caller would then be patched directly into …read more

Continue reading Social Engineering Your Way To The Target PA System→

Arduino Makerbeam Live Plotter Controlled By HTML5 Canvas and Java Website

Posted on by

We’ve never seen someone build a plotter out of buzzwords, but [roxen] did a really good job of it. The idea is simple, place the plotter over a sheet of paper, open a website, draw, and watch the plotter go. Check out the video below the break.

The user draws in an HTML5 Canvas object which is read by a Java Web Server. From there it gets converted to serial commands for an Arduino which controls the steppers with two EasyDrivers.

The build itself is really nice. It perfectly meets the mechanical requirements of a pen plotter without a lot …read more

Continue reading Arduino Makerbeam Live Plotter Controlled By HTML5 Canvas and Java Website→

Get Really Basic With Steppers and Eight Buttons

Posted on by

[Kevin Darrah] put together a good video showing how to control a stepper motor with, not a motor driver, but our fingers. Taking the really low-level approach to do this sort of thing gave us a much better understanding about the features of our stepper driver chips. Such as, for example, why a half step needed twice the current to operate.

[Kevin] starts with the standard explanation of coils, transistors, and magnets that every stepper tutorial does. When he hooks up simple breadboard with passives and buttons, and then begins to activate the switches in sequence is when we had …read more

Continue reading Get Really Basic With Steppers and Eight Buttons→

Materials to Know: Acetal and Delrin

Posted on by

Delrin, Acetal, and its many trade names is a material properly known as Polyoxymethylene or POM. It is one of the strongest plastics and is a good go-to material when you want the best properties of plastic, and don’t need the full strength of a metal part. It was originally formulated to compete with Zinc and Aluminum castings after all.

I won’t go too deep into the numbers behind POM. If you need the Young’s Modulus, you probably don’t need this guide. This is intended to be more of a guide to its general properties. When you’re looking for something …read more

Continue reading Materials to Know: Acetal and Delrin→