Category Archives: Metal

Digital Kiln

Posted on by

A kiln or foundry is too often seen as a piece of equipment which is only available if a hackspace is lucky enough to have one or individuals are dedicated enough to drop the cash for one of their own. [The Thought Emporium] thought that way until he sourced materials to make his own kiln which can also be seen after the break. It costs half the price of a commercial model not including a failed—and exploded—paint can version.

As described in the video, these furnaces are tools capable of more than just pottery and soft metal baubles. Sure, a …read more

Continue reading Digital Kiln→

A Thoughtful Variety of Projects and Failures

Posted on by

Our friends at [The Thought Emporium] have been bringing us delightful projects but not all of them warrant a full-fledged video. What does anyone with a bevy of small but worthy projects do? They put them all together like so many mismatched LEGO blocks. Grab Bag #1 is the start of a semi-monthly video series which presents the smaller projects happening behind the scenes of [The Thought Emporium]’s usual video presentations.

Solar eclipse? There are two because the first was only enough to whet [The Thought Emporium]’s appetite. Ionic lifters? Learn about the favorite transformer around the shop and see …read more

Continue reading A Thoughtful Variety of Projects and Failures→

Wield The Power of Molten Metal

Posted on by

[TheBackyardScientist] at it again with another super villain-esque demonstration of gadgetry: a liquid metal squirt gun.

The squirt gun has a compressed air tank like most others — more on that later — but to fire its primary ammunition, a nozzle that connects directly to an air compressor is needed. Again, like most guns of this nature, air is forced into the gun’s reservoir, displacing the pewter and expelling it out the gun’s barrel. Yes, pewter.

Working around the heat tolerances of thread seal tape, pewter has a low enough melting point that an airtight system is preserved — plus …read more

Continue reading Wield The Power of Molten Metal→

Gateway to Metal Casting

Posted on by

Casting is an exciting and very useful pastime, but it’s not exactly common these days. That’s a problem whether you’re just getting started or have been doing it for years: everyone can use the advice of another. Fear not! The US Department of Energy is here to help with the Industrial Metal’s Program’s Metal Casting cornucopia.

Although not strictly a hack, this is certainly a facilitator of hacks and any experienced user would do themselves some good by perusing the site. Click on the maps to find complex issues presented remarkably well for papers at this level of rigor. Seriously, …read more

Continue reading Gateway to Metal Casting→

DIY Roll Bender Keeps it Simple and Sturdy

Posted on by

If you’ve ever tried to bend a metal pipe or bar over your knee, you’ll know that even lightweight stock requires quite a bit of force. And the force needs to be properly directed, lest the smooth bend you seek become a kink or a crease. When your hands and knees no longer fill the bill, try [MakeItExtreme]’s sturdy and simple roll bender.

As we watched the video below, we had a little déjà vu — hadn’t the [MakeItExtreme] crew built a roll bender for their shop before? Turns out they had, but in reviewing that video, we can see …read more

Continue reading DIY Roll Bender Keeps it Simple and Sturdy→

Earth’s Core Is Squirting a ‘Jet Stream’ of Liquid Metal Under the Surface

Posted on by

Scientists found it by taking a satellite “x-ray” of the globe. Continue reading Earth’s Core Is Squirting a ‘Jet Stream’ of Liquid Metal Under the Surface→

Etching Your Own Metal

Posted on by

It’s been said that with enough soap, one could blow up just about anything. A more modern interpretation of this thought is that with enough knowledge of chemistry, anything is possible. To that end, [Peter] has certainly been doing a good job of putting his knowledge to good use. He recently worked out a relatively inexpensive and easy way to etch metals using some chemistry skill and a little bit of electricity.

After preparing a set of stencils and cleaning the metal work surface, [Peter] sets his work piece in a salt solution. A metal bar is inserted in the …read more

Continue reading Etching Your Own Metal→

Home-Made Metal Brake

Posted on by

Sometimes, the appropriate application of force is the necessary action to solve a problem. Inelegant, perhaps, but bending a piece of metal with precision is difficult without a tool for it. That said, where a maker faces a problem, building a solution swiftly follows; and — if you lack a metal brake like YouTuber [makjosher] — building one of your own can be accomplished in short order.

Drawing from numerous online sources, [makjosher]’s brake is built from 1/8″ steel bar, as well as 1/8″ steel angle. The angle is secured to a 3/4″ wood mounting plate. Displaying tenacity in cutting …read more

Continue reading Home-Made Metal Brake→

Portable Lightweight Foundry

Posted on by

[Makercise] is getting ready for Maker Faire. One of the things he’d really like to do is some casting demonstrations. However, he has no desire to take his expensive and heavy electric kiln based foundry to Maker Faire. So, he made his own.

He got into metal casting during his excellent work on his Gingery lathe series. He started off by modeling his plan in Fusion 360. He’d use a 16qt cook pot turned upside down as the body for his foundry. The top would be lined with ceramic fiber insulation and the lid made out of foundry cement. He …read more

Continue reading Portable Lightweight Foundry→