Author Archives: Richard Baguley

Smartphone Hack For Adding Magnet Power Dock

Posted on by

Here’s a neat hack for making a magnetic charging mount for a cell phone. We know what you’re thinking, but this is definitely not a traditional contactless charging system. Those use magnets but in a different way. This hack involves putting a couple of magnets onto the case of the cell phone, and a couple more on a charging base. You then wire these magnets into the power inputs of the USB port, and a USB cable onto the base, so putting the phone on the base magnets completes the circuit. The magnets themselves become the charging contacts.

It’s a …read more

Continue reading Smartphone Hack For Adding Magnet Power Dock→

Hackaday Dictionary: Software Defined Radio (SDR)

Posted on by

We are entering a new era of radio technology. A new approach to building radios has made devices like multi-band cell phones and the ubiquitous USB TV receivers that seamlessly flit from frequency to frequency possible. That technology is Software Defined Radio, or SDR.

A idealized radio involves a series of stages. Firstly, an antenna receives the radio signal, converting it into an electrical signal. This signal is fed into a tuned resonator which is tuned to a particular frequency. This amplifies the desired signal, which is then sent to a demodulator, a device which extracts the required information from …read more

Continue reading Hackaday Dictionary: Software Defined Radio (SDR)→

Make Your Own ESP8266 Breadboard Adapter

Posted on by

Want to play around with the ESP8266? You’ll need a breadboard adapter, which allows you to connect the ESP8266 to a breadboard as you refine your design. Sure, you could just buy one, but where’s the fun in that?

[Markus Ulsass] designed a simple breadboard adapter for his ESP8266 that can be easily etched and built at home, but which has most of the features of the commercial versions. His adapter features a voltage regulator that can handle anything up to 7 volts and which has reverse polarity protection and a reset switch that puts the ESP8266 into flash mode, …read more

Continue reading Make Your Own ESP8266 Breadboard Adapter→

Bluetooth Water Cannon Junk Build Shoots Into Our Hearts

Posted on by

We’ve seen a few remote controlled turret builds in the past, but this one from [Noel Geren] is pretty neat: it shoots water and uses Bluetooth Low Energy (BLE) for control. Check it out in action in the video below.

[Noel] used the guts of a Nerf Thunderstrike water gun for the firing mechanism, combined with a 3D-printed enclosure and a servo that rotates the turret top. The pump from the gun is connected to a simple relay that replaces the trigger. Both the relay and the servo are connected to an RFDuino with a servo shield, which is programmed …read more

Continue reading Bluetooth Water Cannon Junk Build Shoots Into Our Hearts→

Quieting a Cheap LCD Projector

Posted on by

There’s an old saying along the lines of “You pay peanuts, you get monkeys”. That’s true of technology, too, but a good hacker can sometimes teach an old monkey new tricks. [Heye] bought an LCD projector for $60 off AliExpress, and it turned out to be rather noisy: the air fan that sucked in air to cool the LED light source made a whooshing noise.

No surprise there, but rather than give up, he decided to see what he could do about the noise. So, he took the projector apart. After some excavation, he realized that the main source of …read more

Continue reading Quieting a Cheap LCD Projector→

Critter Twitter Trap Traps Critters, Pings Twitter

Posted on by

Got aliens in your attic? Squirrels in the skirting board? You need a trap, and [John Mangan] has come up with an interesting way to let you know that you have caught that pesky varmint: the IoT Critter Twitter Trap. By adding a ball switch, Electric Imp and a couple of batteries to a trap, he was able to set the trap to notify him when it caught something over Twitter. To do this, he programmed the Electric Imp to send a message over when a varmint trods on the panel inside the trap, slamming its door shut. The whole …read more

Continue reading Critter Twitter Trap Traps Critters, Pings Twitter→

Steam-Powered Raspberry Pi Zero Doesn’t Get Any More Steampunk

Posted on by

Steampunk usually involves sticking a few old valves on your laptop and riding a penny farthing, but [Alexzpro] understands the real thing: he just created a steam powered Raspberry Pi Zero (translated).

His setup is a little lashed together, but works it’s a throwback to electricity generation of old and deserves the steampunk moniker. A steam boiler drives a steam turbine, which turns a motor, generating electrical power. This feeds into a regulator and a bank of capacitors that smooths the voltage out to a nice even 5 Volts, which powers the Pi.

It’s not exactly efficient, but running the …read more

Continue reading Steam-Powered Raspberry Pi Zero Doesn’t Get Any More Steampunk→

Wall-E Goes Corporate, Offering Telepresence Service

Posted on by

I guess if you are going to build a robot to do something boring like telepresence, you might as well make it cute. That’s obviously what [Andrew Maurer] was thinking when he built a telepresence robot using a Wall-E toy. The result is kind of adorable: Wall-E is holding the 5-inch HDMI screen that shows the video, and can scoot around in true Pixar fashion under remote control.

It’s also a neat build on the inside, using a Raspberry Pi for the brains and an Adafruit MotorHat to control the motors. The original toy didn’t have motors, so he added …read more

Continue reading Wall-E Goes Corporate, Offering Telepresence Service→