Author Archives: Bob Baddeley

Hackaday Dictionary: Mils and Inches and Meters (oh my)

Posted on by

Measuring length is a pain, and it’s all the fault of Imperial measurements. Certain industries have standardized around either Imperial or metric, which means that working on projects across multiple industries generally leads to at least one conversion. For everyone outside the last bastion of Imperial units, here’s a primer on how we do it in crazy-land.

Definitions

The basic unit of length measurement in Imperial units is the inch. twelve inches make up one foot, three feet make up one yard, and 5,280 feet (or 1,760 yards) make up a mile. Easy to remember, right?

Ironically, an inch is …read more

Continue reading Hackaday Dictionary: Mils and Inches and Meters (oh my)→

Firearm Tech – Are Smart Guns Even Realistic?

Posted on by

At frustratingly regular intervals, the debate around gun control crops up, and every time there is a discussion about smart guns. The general idea is to have a gun that will not fire unless authenticated and authorized. There’s usually a story about a young person who invents a smart controller and another company that is struggling because they just can’t get “Big Guns” to buy into the idea. We aren’t going to focus on the politics; we’re going to look at whether the technology is realistic, and why a lot of the news stories about new tech never pan out. …read more

Continue reading Firearm Tech – Are Smart Guns Even Realistic?→

Tools of the Trade – Through Hole Assembly

Posted on by

In our last installment of Tools of the Trade, we had just finished doing the inspection of the surface mount part of the PCB. Next in the process is the through hole components. Depending on the PCB, the order may change slightly, but generally it makes more sense to get all the SMT work done before moving to the through hole work.

Through hole used to be the standard, but as the need for size reduction and automation increased, SMT gained favor. However, there are still a lot of reasons to use through hole components, so they aren’t going away …read more

Continue reading Tools of the Trade – Through Hole Assembly→

Bunnie and Snowden Explore IPhone’s Hackability

Posted on by

[Bunnie Huang] and [Edward Snowden] have teamed up to publish a paper exploring the possibility of introspection on the iPhone.

The idea is that phones are increasingly complex and potentially vulnerable to all kinds of digital surveillance. Even airplane mode is insufficient for knowing that your phone isn’t somehow transmitting information. The paper looks at the various radios on the iPhone, going so far as opening up the device and reading signals at each of the chips for cell, WiFi, Bluetooth, GPS, and NFC to determine whether the chip itself is doing anything, regardless of what the screen says. This …read more

Continue reading Bunnie and Snowden Explore IPhone’s Hackability→

Tools of the Trade – Inspection

Posted on by

In the last episode, we put our circuit boards through the reflow process. Unfortunately, it’s not 100% accurate, and there are often problems that can occur that need to be detected and fixed. That’s what the inspection step is for. One could insert an inspection step after paste, after placement, and after reflow, but the first two are icing on the cake — the phase where most mistakes can be caught is after reflow.

There are a number of problems typical with a surface mount reflow process:

  • Tombstoning – This is when a component stands up vertically. This is bad

…read more

Continue reading Tools of the Trade – Inspection→

Why Kickstarter Products Fail

Posted on by

It seems every week we report on Kickstarter campaigns that fail in extraordinary fashion. And yet there are templates for their failure; stories that are told and retold. These stereotypical faceplants can be avoided. And they are of course not limited to Kickstarter, but apply to all Crowd Funding platforms. Let me list the many failure modes of crowdfunding a product. Learn from these tropes and maybe we can break out of this cycle of despair.

Failure Out of the Gate

You don’t hear about these failures, and that’s the point. These are crowd funded projects that launch into the …read more

Continue reading Why Kickstarter Products Fail→

SATA Cable Replaces DC Motor Brushes as Macgyver Looks On

Posted on by

[dmalhar] was digging around in his bins for motors and found one with missing brushes. Being resourceful (and not able to find another motor), he managed to tear apart a SATA cable and form the pins into brushes with just the right amount of spring. Yes, this looks like a cheap motor, but in the moment of necessity availability wins, and this hack is truly commendable. If he had used a paperclip, MacGyver would have been proud, but the SATA cable pins make us proud.

Normally the brushes of DC motors are made with a graphite or some other material …read more

Continue reading SATA Cable Replaces DC Motor Brushes as Macgyver Looks On→

Tools of the Trade – Solder Paste Dispensing

Posted on by

The general process of circuit board assembly goes like this: You order your PCBs. You also order your components. For surface mount components, you apply solder paste to the pads, put the components on top, and then heat the board up so the solder paste flows and makes a bond. Then for through hole components you put the leads through the holes, and solder them with an iron or a solder wave or dip. Then you do an inspection for defects, program any microcontrollers, and finally test the completed board to make sure everything runs.

The tricky part is in …read more

Continue reading Tools of the Trade – Solder Paste Dispensing→

Bullet-time Video Effect by Throwing Your Phone Around

Posted on by

Ski areas are setting formal policies for drones left and right, but what happens when your drone isn’t a drone but is instead a tethered iPhone with wings swinging around you like a ball-and-chain flail as you careen down a mountain? [nicvuignier] decided to explore the possibility of capturing bullet-time video of his ski runs by essentially swinging his phone around him on a tether. The phone is attached to a winged carrier of his own design, 3D printed in PLA.

One would think this would likely result in all kinds of disaster, but we haven’t seen the outtakes yet, …read more

Continue reading Bullet-time Video Effect by Throwing Your Phone Around→